RCFoamCutter - Small Foam Cutters
Basic Package - Kit - $800 - Out of Stock
The Basic Package includes mechanical parts only.
​
Parts Included:
The Basic package includes the mechanical parts only
4 long shafts - 20" long
4 short shafts - 10" long
2 long ACME screws - 8mm (will need 8mm coupler / motor shaft diameter)
2 short ACME screws - 8mm (will need 8mm coupler / motor shaft diameter)
All metal parts
***Electronics, motors, hot wire power supply - not included
Recommended Software:
Mach3 to run the machines can be found at machsupport.com
DevCad to generate the GCode can be found at DevCAD.com Select DevFoam for straight cuts and DevFoamPro for tapered cuts
Full Package - Out of Stock
Kit - $1800
Fully assembled - $2200
The Full Package includes mechanical and electronic parts.
​
Parts included:
4 long shafts - 24" long
4 short shafts - 12" long
2 long ACME screws + couplers
2 short ACME screws + couplers
4 motors with cables - no soldering required
All metal parts
Electronics and motors (not enclosed in a case - see picture below)
***Hot wire power supply and hot wire - not included
Please note - This is a parallel port electronic board - it will run with WinXP and Win7 32 bit only
For Win7 64 bit or Win8 or Win10, UC100 adapter is available here
Recommended Software:
Mach3 to run the machines can be found at machsupport.com - for more information visit our tutorials on how to setup Mach3
DevCad to generate the GCode can be found at DevCAD.com Select DevFoam for straight cuts and DevFoamPro for tapered cuts
+
+
Complete Package - Out of Stock
Kit - $2800
Fully Assembled - $3200
The Complete Package includes mechanical and electronic parts
​
Parts included:
4 long shafts - 30" long
4 short shafts - 14" long
2 long ACME screws + couplers
2 short ACME screws + couplers
4 motors with cables - no soldering is required
All metal parts
4 axis stepper motor electronics box - fully assembled and tested
Hot wire power supply - will heat up to 40" of hot wire + hot wire
Please note - This is a parallel port electronic box - it will run with WinXP and Win7 32 bit only
For Win7 64 bit or Win8 or Win10, UC100 adapter is available here
Recommended Software:
Mach3 to run the machines can be found at machsupport.com - for more information visit our tutorials on how to setup Mach3
DevCad to generate the GCode can be found at DevCAD.com Select DevFoam for straight cuts and DevFoamPro for tapered cuts
+
+
Complete Package Extended 32"x13"x50" - Out of Stock
Kit - $3500
Fully Assembled - $3900
The Complete Package Extended includes mechanical and electronic parts
​
Parts included:
4 long shafts - 36" long
4 short shafts - 16" long
2 long ACME screws + couplers
2 short ACME screws + couplers
4 motors with cables - no soldering is required
All metal parts
4 axis stepper motor electronics box - fully assembled and tested
Hot wire power supply - will heat up to 50" of hot wire + hot wire
Please note - This is a USB version - will run on Win7, Win8 and Win10
Recommended Software:
Mach3 to run the machines can be found at machsupport.com - for more information visit our tutorials on how to setup Mach3
Driver for the UC100 (Mach3 USB driver) can be found here
DevCad to generate the GCode can be found at DevCAD.com Select DevFoam for straight cuts and DevFoamPro for tapered cuts
+
